Advertising
FWIW just looked in the manual and they do just say track “the blade” central on the tyre. No specific mention of the gullet position. Will post some pictures tomorrow if you still need them If at first you don't succeed, destroy all evidence that you tried. ELEKTRA BECKUM 315 BAND SAW ISSUE #1201574. I have recently bought a benchtop bandsaw as a second saw, I have an Electra Beckum BAS 315 and wanted a small saw for use in my cellar workshop. I did a lot of on-line searching before deciding on a Charnwood W711 watch the video, it really does cut as shown.
BAS 315/450
GB
Application
Especially suitable for guiding the band saw blade where absolute precise cuts are required. The thrust bearing´s body
is hardened and precision groung, with Tungsten Carbide rims.
The advantages of the Precision Blade Guide over the Standard Blade Guide:
is hardened and precision groung, with Tungsten Carbide rims.
The advantages of the Precision Blade Guide over the Standard Blade Guide:
- improves versatility of the machine
- extended thrust bearing service life
- no tools required for thrust bearing setting and replacing
- suitable for machines with clockwise or counter-clockwise direction of rotation
- extended thrust bearing service life
- no tools required for thrust bearing setting and replacing
- suitable for machines with clockwise or counter-clockwise direction of rotation
User Responsibility
This accessory is designed and intended for use on band sawing machines and will perform in conformity with the
description contained in this manual. This accessory or any of its parts should not be altered from standard
specifications. The user of this accessory shall have the sole responsibility for any malfunction which results from
improper use or unauthorized modification from standard specifications, faulty maintenance, damage or improper repair
by anyone other than qualified persons approved by ELEKTRA BECKUM or their representatives.
description contained in this manual. This accessory or any of its parts should not be altered from standard
specifications. The user of this accessory shall have the sole responsibility for any malfunction which results from
improper use or unauthorized modification from standard specifications, faulty maintenance, damage or improper repair
by anyone other than qualified persons approved by ELEKTRA BECKUM or their representatives.
Important
Before installing the Precision Blade Guide, the saw band guard must be
shortened by 45 mm, so the blade can still be changed when the Precision
Blade Guide is installed.
Loosen wing nut (135) and set blade guard ass'y (12) to lowest position, until
standard roller guide ass'y rests on the table. Remove the 4 raised countersunk
head screws (212) with Philips #2 screwdriver. Use a hacksaw to cut off
45 mm from the saw band guard as indicated in the drawing below.
Reinstall saw band guard.
shortened by 45 mm, so the blade can still be changed when the Precision
Blade Guide is installed.
Loosen wing nut (135) and set blade guard ass'y (12) to lowest position, until
standard roller guide ass'y rests on the table. Remove the 4 raised countersunk
head screws (212) with Philips #2 screwdriver. Use a hacksaw to cut off
45 mm from the saw band guard as indicated in the drawing below.
Reinstall saw band guard.
LINE OF CUT
![Bas Bas](/uploads/1/2/5/8/125874928/889989226.jpg)
Lowering the Table
Installing the Precision Blade Guide
requires lowering the band saw table.
Remove table completely from frame
and use drilling template provided to
mark position of the new holes
required. Drill four holes Ø 8.5 mm in
exact position and debur edges. With
the Precision Blade Guide installed
the maximum height of cut is reduced
by 15 mm.
requires lowering the band saw table.
Remove table completely from frame
and use drilling template provided to
mark position of the new holes
required. Drill four holes Ø 8.5 mm in
exact position and debur edges. With
the Precision Blade Guide installed
the maximum height of cut is reduced
by 15 mm.
Note! The carriage bolt M8x30,
located on the underside of the table,
must be replaced by the carriage
bolt M8x50 supplied (pos. 100 or
spacer bush 8x24).
This bolt serves as stop when tilting
the table back to the 90
located on the underside of the table,
must be replaced by the carriage
bolt M8x50 supplied (pos. 100 or
spacer bush 8x24).
This bolt serves as stop when tilting
the table back to the 90
°
position.
Existing holes
New holes
Drilling pattern
5
Advertising
Popular Brands
Popular manuals
User Manuals, Guides and Specifications for your Elektra Beckum BAS 315 Saw. Database contains 3 Elektra Beckum BAS 315 Manuals (available for free online viewing or downloading in PDF): Manuel, Manual , Instruction manual .
Elektra Beckum BAS 315 Instruction manual (7 pages)
Pages: 7 | Size:Elektra Beckum BAS 315 Manual (19 pages)
Pages: 19 | Size: 0.11 MbElektra Beckum BAS 315 Manuel (4 pages)
Pages: 4 | Size: 0.08 Mb